Communications Setup

<< Click to Display Table of Contents >>

Navigation:  Sensor Platforms > Breadometer® > Setup >

Communications Setup

SuperM.O.L.E.® Gold 2

Direct Connect:

Prior to operation the M.O.L.E. Profiler must be configured to properly communicate with the M.O.L.E.® MAP Software.

Important Information

The M.O.L.E.® MAP software must be installed prior to communications setup. (Refer to Software Installation for more information).

To connect the M.O.L.E. Profiler:

1)Insert the USB computer interface cable into a computer USB Port and the other end into the Data/Charging Port.

M.O.L.E. Profiler Connection

Important Information

In some cases, the first time a M.O.L.E. Profiler is connected to a computer with an Windows XP operating system, it may require two drivers to be installed. One is a device driver for the M.O.L.E. Profiler and the other is for USB communication.

2)During installation of the device driver, when prompted to select the location of the device driver, select "Install the software automatically". Follow the remaining wizard instructions closely.

mm_driver_install-1

3)During installation of the USB driver a message box appears, select the Continue Anyway command button and the driver will be successfully installed.

mm_driver_install_warning

4)After M.O.L.E. Profiler is connected to a computer, the software must be configured so they can communicate. Start the software program by either double-clicking the M.O.L.E.® MAP software icon or selecting it from the ECD program sub-menu.

Start Program

5)On the M.O.L.E. menu, click the Select Instrument command.
6)Select the desired instrument from the dialog box. If there are none displayed, click the Scan for Instruments command button to detect all available instruments.

Select Instrument

Important Information

If the software does not detect a M.O.L.E. Profiler, using the communication cable connect it to the computer and click the Scan for Instruments command button to search again. M.O.L.E.® MAP software allows multiple instruments to be connected to a computer at one time. Selecting the Scan for Instruments command button will detect all instruments and display them in the dialog box. If no instrument is detected the software displays all of the Demonstration thermal profilers to select from.

7)Click the OK command button to accept or Cancel to quit the command.

SuperM.O.L.E.® Gold

Prior to operation the M.O.L.E. Profiler must be configured to properly communicate with the M.O.L.E.® MAP Software.

Important Information

The M.O.L.E.® MAP software must be installed prior to communications setup. (Refer to Software Installation for more information).

To connect the M.O.L.E. Profiler:

1)Locate the computer Interface cable and plug the 9-pin connector into a computer COM Port and the other end into the M.O.L.E. Profiler Data Port.

Important Information

If no Serial Port exists, use the included USB adaptor to connect the interface cable to the computer.

M.O.L.E. Profiler Connection

2)After the computer interface cable is connected to a computer, the Communication (COM) Port must be configured in the software to match the same COM Port as the computer so they can communicate.
3)Start the software program by either double-clicking the M.O.L.E.® MAP software icon or selecting it from the ECD program sub-menu.

Start Program

4)On the M.O.L.E. menu, click the Select Instrument command.
5)Select the desired instrument from the dialog box. If there are none displayed, click the Scan for Instruments command button to detect all available instruments.

supermolegold-0000

Important Information

If the software does not detect a M.O.L.E. Profiler, using the communication cable connect it to the computer and click the Scan for Instruments command button to search again. M.O.L.E.® MAP software allows multiple instruments to be connected to a computer at one time. Selecting the Scan for Instruments command button will detect all instruments and display them in the dialog box. If no instrument is detected the software displays all of the Demonstration thermal profilers to select from.

6)Click the OK command button to accept or Cancel to quit the command.